Aerospace Engineering Excellence
Pioneering UnmannedAerospace Innovation
Leading independent engineering company delivering cutting-edge aviation solutions with uncompromising excellence.
Aerospace Capabilities
Explore our comprehensive unmanned aerial systems engineering services
01
HIGH LEVEL SYSTEMS ARCHITECTURE
- ▸ARCHITECTURE BASED ON WEIGHT
- ▸SPECIFIC CONSTRAINTS
- ▸IDENTIFY KEY SUBSYSTEMS AND INTERFACES
02
CLASS-1: PRELIMINARY DESIGN
- ▸THEORETICAL DESIGN
- ▸WEIGHT ESTIMATION
- ▸AERODYNAMIC ANALYSIS
- ▸STABILITY AND CONTROL ANALYSIS
03
CLASS-2: PRELIMINARY DESIGN
- ▸3D EXTERNAL VISUALIZATION
- ▸WEIGHT AND BALANCE
- ▸HIGH FIDELITY AERODYNAMICS ANALYSIS
04
PROPULSION SYSTEMS ANALYSIS
- ▸SELECTION OF PROPULSION SYSTEM
- ▸RUBBER ENGINE SIZING
- ▸FINALIZE ENGINE SELECTION
01
STRUCTURAL REQUIREMENTS & LAYOUT
- ▸LOAD CASE IDENTIFICATION
- ▸OPTIMIZED INTERNAL GEOMETRY
- ▸ALLOWABLE STRESS & STRAIN LIMITS
- ▸DESIGN FOR MANUFACTURABILITY (DFM)
02
MATERIAL SCIENCE & SELECTION
- ▸COMPOSITE & ALLOY CHARACTERIZATION
- ▸OPERATIONAL ENVIRONMENT ASSESSMENT
- ▸RIGIDITY-TO-WEIGHT RATIO
- ▸EMC SHIELDING
03
STATIC AND DYNAMIC ANALYSIS
- ▸FINITE ELEMENT MODELING
- ▸ELASTIC DEFORMATION AND BUCKLING
- ▸MODAL & VIBRATION RESPONSE TESTING
- ▸AEROELASTICITY (FLUTTER) PREVENTION
04
DURABILITY AND DAMAGE TOLERANCE
- ▸FATIGUE LIFE ESTIMATION
- ▸ACCIDENTAL DAMAGE RESISTANCE
- ▸INSPECTION & MAINTENANCE SCHEDULES
- ▸LIFE-CYCLE INTEGRITY VERIFICATION
01
JIGS, FIXTURES, INTEGRATION
- ▸PRECISION JIGS & FIXTURES DESIGN
- ▸TOOLING FOR AEROSPACE STRUCTURES
- ▸STRUCTURAL SYSTEMS INTEGRATION
- ▸ASSEMBLY PLANNING, VALIDATION & SUPPORT
02
ENVIRONMENTAL QUALIFICATION
- ▸TEMPERATURE & ALTITUDE EXTREMES
- ▸ENVIRONMENTAL STRESS SCREENING (ESS)
- ▸SALT FOG & CORROSION RESISTANCE
- ▸THUNDERSTORM & LIGHTNING STRIKE PROTECTION
03
DYNAMIC & VIBRATION QUALIFICATION
- ▸RANDOM VIBRATION & SHOCK TESTING
- ▸IMU DAMPING
- ▸DYNAMIC BALANCING OF ROTATING PARTS
- ▸ENDURANCE & HIGH-CYCLE FATIGUE
04
AEROMECHANICAL CERTIFICATION SUPPORT
- ▸AIRWORTHINESS COMPLIANCE (FAR/CS/MIL)
- ▸CERTIFICATION DOCUMENTATION
- ▸CERTIFICATION SUPPORT
01
GUIDANCE & TRAJECTORY GENERATION
- ▸WAYPOINT SEQUENCING & MANAGEMENT
- ▸AFFORDANCE-BASED PATH FOLLOWING
- ▸YAW & HEADING COMMAND GENERATION
- ▸SPLINE TRAJECTORY PROFILES
02
NAVIGATION & STATE ESTIMATION
- ▸GLOBAL POSITIONING & GNSS INTEGRATION
- ▸PROPRIOCEPTIVE SENSOR FILTERING (EKF)
- ▸STATE ESTIMATION & DEAD RECKONING
- ▸TEMPORAL SYNCHRONIZATION OF DATA
03
CONTROL LAW & INNER-LOOP STABILITY
- ▸PROPORTIONAL-INTEGRAL-DERIVATIVE (PID) TUNING
- ▸LINEAR QUADRATIC REGULATOR (LQR) DESIGN
- ▸OUTPUT FEEDBACK & GAIN SCHEDULING
- ▸TRANSIENT RESPONSE OPTIMIZATION
04
ROBUSTNESS & ADAPTIVE CONTROL
- ▸FAILURE MODE HANDLING & RECOVERY
- ▸LOSS OF LINK (LOL) MITIGATION LOGIC
- ▸OUTSIDE-DISTURBANCE (WIND) REJECTION
- ▸WING-LEVELING & AUTO-TRIM FUNCTIONS
01
ASSEMBLY & INTEGRATION (A&I)
- ▸PRECISION MECHANICAL INTEGRATION
- ▸UNIT-LEVEL FUNCTIONAL TESTING
- ▸LOOM & HARNESS ROUTING OPTIMIZATION
- ▸SYSTEM-LEVEL POWER-ON PROCEDURES
02
INTERFACE & PROTOCOL ALIGNMENT
- ▸HARDWARE-IN-THE-LOOP (HIL) TESTING
- ▸UNIFIED COMMUNICATION PROTOCOLS
- ▸BUS ARCHITECTURE SYNCHRONIZATION
- ▸SUBSYSTEM INTERFACE CONTROL (ICD)
03
VERIFICATION & VALIDATION (V&V)
- ▸COMPLIANCE WITH DESIGN STANDARDS
- ▸OPERATIONAL READINESS REVIEWS
- ▸REQUIREMENTS TRACEABILITY MATRIX
- ▸END-TO-END FUNCTIONAL VALIDATION
04
OPERATIONS & LIFECYCLE SUPPORT
- ▸FLEET MANAGEMENT & HEALTH MONITORING
- ▸LOGISTICS & SUPPLY CHAIN INTEGRATION
- ▸ENVIRONMENTAL IMPACT ASSESSMENT
- ▸TECHNICAL MANUALS & PILOT TRAINING